增益分级，精准测量RTM Audio Stage v2.0.8 U2B [MacOSX]

GUISEPPE | 20 July 2026 | 13 MB

STAGE
增益分级，精准测量。A/B

对比，绝不出错。一个插件，两种工具。STAGE 只需一次无咔嗒声的微调，即可将电平调整到您选择的目标值，然后链接到所有通道，因此一个实例即可同时处理整个混音。EVEN 允许您在完全匹配的响度下比较两个信号链，即使是盲听也能做到，因此音调判断绝不会被音量所左右。

两个工具，一个插件
。正确设置电平，聆听真实声音。STAGE
在您处理之前确保电平准确。EVEN 在您处理过程中始终保持准确。STAGE自动增益分级：

STAGE会监听您最响亮的通道并测量其电平（第 95 百分位），而不是任何无关的瞬态信号。然后，它会建议一次静态微调，使该通道达到您的目标值。无增益叠加，无抽吸，无音染。峰值、RMS、VU 或 LUFS。EVEN响度匹配 A/B：更响亮的声音总是更好，因此公平的 A/B 对比必须进行电平匹配。即使两条路径的感知响度相同，也可以盲选并投票，然后显示结果。评判的是声音，而不是音量。在 STAGE One 中，只需进行一次精确的增益调整。仅此而已。一次固定的增益调整不会添加任何音染、抽吸效应或延迟。这是你能对信号做的最透明的操作，而且由于它始终保持不变，你的混音将保持可预测性。01测量响度通道始终监听，无需启动按钮。持续监测95 % 分位电平：响度足以产生影响，并且能够抵御一次性瞬态干扰。02你的目标，你的指标将通道调整到峰值、RMS、VU 或 LUFS 的目标值。快速设置模拟、流媒体、高电平和俱乐部电平。03 SOURCE预设人声、鼓、贝斯或母带 将目标值和指标配对设置，STAGE 甚至可以为你猜测音源。04真峰值安全：STAGE 在设置好增益后，会运行 4 倍过采样采样间检查，并显示增益调整后的 dBTP 值（绿色表示通过编解码器验证）。05无咔嗒声，即时响应：增益调整采用10毫秒的渐变过程，因此不会产生咔嗒声，也不会增加延迟。06一键设置整个混音：每个 STAGE 都是一个卫星。它们在整个会话中相互连接，因此一个主实例可以触发所有卫星实例。只需单击一次“全部设置”，每个通道即可达到目标增益：一键完成整个混音的增益设置。

STAGE
Gain-staging that measures. A/B that never lies.

Two tools in one plug-in. STAGE sets your level with a single, click-free trim to the target you choose, then links across every channel so one instance can stage the whole mix at once. EVEN lets you compare two chains at exactly matched loudness, even blind, so tone calls are never fooled by volume.

Two tools, one plug-in
Set the level right. Then hear the truth.
STAGE gets your levels honest before you process. EVEN keeps you honest while you do.

STAGE
Automatic gain-staging
STAGE listens to your loudest pass and measures it, the 95th-percentile level, not one stray transient. Then it suggests a single static trim to land that pass on your target. No riding, no pumping, no colour. Peak, RMS, VU or LUFS.

EVEN
Loudness-matched A/B
Louder always sounds better, so a fair A/B has to be level-matched. EVEN gains the two paths to equal perceived loudness, switch blind and vote, then reveal the tally. Judge the sound, never the volume.

Inside STAGE
One measured trim. Nothing else.
A single fixed gain change adds zero colour, zero pumping, zero latency. It is the most transparent thing you can do to a signal, and because it never moves, your mix stays predictable.

01
Measures the loud pass
Always listening, no arm button. A running 95th-percentile level: loud enough to matter, robust against a one-off transient.

02
Your target, your metric
Land the pass on a target in Peak, RMS, VU or LUFS. Quick pills for the analog, streaming, hot and club levels.

03
SOURCE presets
Vocal, Drum, Bass or Master set the target and metric as a pair, and STAGE even guesses the source for you.

04
True-peak safe
After it sets the trim, STAGE runs a 4× oversampled inter-sample check and tells you the post-trim dBTP, green when it survives the codec.

05
Click-free, instant
The trim applies over a 10 ms ramp, so there is never a click, and it adds no latency to your chain.

06
One click stages the whole mix
Every STAGE is a satellite. They link to each other across the session, so one main instance can trigger them all. Hit SET ALL once and every channel lands on its target: a full mix gain-staged in a single click.

https://www.rtmaudio.com/stage/